| MICRO LATHE
BASIC UNIT |
|
CAPACITY L 1017
Swing over bed 4 1/2" (Max. turning dia. 4 1/2")
Swing over crosslide 2 3/8" DIA.
Overall length of bed 15 1/2”
Overall length of lathe 16 1/2”
Tool bit size std. 1/4"
Distance between centers 9 3/4” (tailstock optional)
Carriage travel 9"
Crosslide travel 1 3/4"
SPINDLE
Sealed precision ball 1.548 O.D., .6692 I.D.
Spindle nose 3/4"-16 (3/4 SAE)
Spindle hole .343
Spindle l.D. taper 15 degrees (30 degrees included)
Max. collet dia. 7/32"
Pulley size 5’8” bore
|
| TAIG Micro Lathe & Accessory
Price List |
| PART# |
PRICE |
DESCRIPTION |
| L 1017 |
184.75 |
Micro Lathe Basic Unit, factory assembled with tool post & carriage
stop depth, 15” bed (pulleys, tailstock not included)
|
ZK 1019
|
153.10 kit
|
Unassembled Micro Lathe Parts Kit, headstock pre-assembled,
no machining needed. (pulleys, tailstock not incl.) |
1020
|
72.15 Ea. |
WW Spindle Cartridge, no housing (use WW jewelers collets only) |
1020A
|
98,60 Ea.
|
WW Spindle Headstock Assembly with pulley and drawbar (use
WW jewelers collets
only) |
| 1020B |
31.80 add |
WW Spindle and drawbar in Lathe - in lieu of standard (use
WW jewelers collets
only) |
1021W |
98.50 ea. |
Motor, 1/4 H.P~ 1725 R.P.M. 115 V, 1 Phase, 60 HZ, 48 Frame,
6.0 Amps, 1.0 S.F 1/2” Shaft pre-wired witch, cord
|
1022
|
5.00 ea. |
Motor Mount Bracket with necessary hardware, fits above motor
and Nema 48 frame motors |
1023
|
7.50 ea. |
Mounting Board, 12”x 18" (motor mount bracket not included) |
1024
|
7.50 ea. |
Mounting Board, 8”x 24” (motor mount bracket not
included) |
| 1026 |
4.00 ea. |
Depth-Stop for work piece in chuck |
1030* |
63.50ea. |
4-Jaw Chuck, 3-1/4” diameter, 3/4-16 thread mount,
jaws adjust independently (reversible heat treated steel jaws) |
1034
|
9.25 ea. |
Lathe Dog, holds work piece while turning between centers |
1035
|
14.30 ea. |
Face Plate, 3-1/4”, 3/4-16 Thread mount |
1036
|
5.60 set |
Face Plate Angle Bracket Set |
| 1037 |
7.80 ea. |
Face Plate, 2” diameter (wood turners) |
1037.3H |
10.15 ea. |
Face Plate, 2” diameter with three holes drilled (wood
turners) |
1038
|
26.75 ea.
|
Tool Rest, 4” swivel joint, height adjustable (wood turners) |
1040*
|
29.85 ea.
|
Collet Set, one collet closer with eight collets, sizes 1/8,
5/32, 3/16, 7/32, 1/4, 9/32, 5/16 and one blank |
1041A *
|
4.15 ea.
|
1/8 Collet |
| 1041B* |
4.15 ea. |
5/32 Collet |
1041C* |
4.15 ea. |
3/16 Collet |
1041D*
|
4.15 ea. |
7/32 Collet |
1041E*
|
4.15 ea. |
1/4 Collet |
1041F*
|
4.15 ea. |
9/32 Collet |
| 1041G * |
4.15 ea. |
5/16 Collet |
1042 * |
5.40 Ea. |
Collet Closer |
1043*
|
2.90 set
|
Four Blank Collets, furnished unslotted for making special
arbors (may be bored and slotted) |
| 1050* |
63.10 ea.
|
3-jaw Chuck, 3-1/4w diameter, 3/4.16 thread, self-centering
scroll (steel body)
with reversible aluminum soft jaws |
| 1051 |
7.90 set
|
Additional Blank Soft Jaw Set |
| 1052 |
7.75 Ea. |
Full Circle Soft Jaw for 3-jaw chuck |
1060* |
71.40 Ea. |
4-Jaw Chuck, 3-1/4” diameter, 3/4-16 thread, self-centering
scroll (steel body) with reversible aluminum soft jaws |
1090*
|
36.25 Ea.
|
0-1/4” Jacobs Drill Chuck, industrial quality, 3/8-24
thread |
1091 *
|
9.90 Ea.
|
0-1/4” Jacobs Drill Chuck, commercial quality, 3/8-24
thread |
1092 *
|
10.20 Ea.
|
1/16.~3/8” Jacobs Drill Chuck, commercial quality, 3/8-24
thread |
| 1093* |
19.20Ea. |
1/8-1/2” Jacobs Drill Chuck, commercial quality, 3/8-24
thread |
1095 |
27.60 set
|
Tool Bit Set, six-piece high-speed steel: Left Hand, Right
Hand, 45° Chamfer, Round Nose, Boring Bar & Cut Off |
1096
|
1.95 Ea.
|
Unground Tool Bit, 1/4” square |
1097A
|
5.05 Ea.
|
Left Hand Tool Bit |
1097B
|
5.05 Ea.
|
Right Hand Tool Bit |
| 1097C |
5.05 Ea. |
45° Chamfer Tool Bit |
1097D |
5.05 Ea. |
Round Nose Tool Bit |
1097E
|
5.05 Ea.
|
Boring Bar Tool Bit |
1097F
|
5.05 Ea.
|
Cut Off Tool Bit |
1110 *
|
5.60 Ea.
|
Slitting Saw Arbor, screws directly on spindle, wrench included |
| 1111 * |
12.00 Ea. |
High Speed Slitting Saw .032 x 2-1/2” diameter |
1120 |
6.20 Ea. |
Grinding Wheel Arbor, screws directly on spindle |
1122
|
7.00 Set |
Grinding Wheel Set |
1130
|
3.90Ea.
|
Blank Arbor 1.00” diameter, screws directly on spindle
(may be machined for
special jobs) |
1132
|
2.60 Ea.
|
Blank Arbor |
| 1140 |
10.90 Ea. |
Drill Chuck Arbor, attaches Jacobs chucks to spindle, 3/8-24
thread |
1150
|
38.20 Ea.
|
Drilling Tailstock, lever operated, 5/8” off-set with
dead center, 3/8-24 thread |
1151
|
15.80 Ea.
|
Needle Bearing Center, spring loaded |
1152
|
15.90 Ea.
|
Die Holder for Tailstock (will accept 13/16” and 1.00” button
dies) |
1159 *
|
7.90 Ea.
|
Spare Gates Polyurethane V-Belt, #3M 315, 12-1/2” flat
length (est. belt
life 5000 hrs.) |
| 1160 |
7.90 Ea. |
Spare Gates Polyurethane V-Belt, #3M 500,20” flat length
(est. belt life
- 5000 hrs.) |
1161
|
24.45set
|
Six-Step Pulley Set (two pulleys per set) 3/8" motor
shaft, 3M 500 belt included. |
1162
|
24.45 set
|
Six-Step Pulley Set (two pulleys per set) 1/2” motor
shaft, standard 3M 315 heft included (3M 500 belt optional) |
1170
|
4.60 Ea. |
Extra Tool Post (same as supplied with Lathe) |
1171
|
4.95 Ea.
|
Back Tool Post, tool bit mounts upside down (two tools may
be used at same time) |
| 1173 |
27.90 Ea.
|
T-Bar Cut-off Tool, height adjustable |
1190
|
24.80 Ea.
|
Steady Rest 3/32" to 1-1/2” capacity |
1200
|
44.60 Ea.
|
Top Slide (compound), mounts on cross slide for cutting tapers
and angles with tool post |
1210
|
19.85 Ea.
|
Radius Turner, swings tool bit in arc (makes balls) |
1220
|
61.70Ea.
|
Milling Attachment, mounts directly on cross slide (2 x 3.3/4” table) |
| 1221 * |
14.45 Ea. |
3/4-16 Chuck Adapter, adapts chuck to mill table |
1224 * |
19.50 Ea.
|
Fly Cutter, 1-1/4 to 2-1/2” diameter, 3/4-16 thread
mount, tool bit included |
1225*
|
26.75Ea.
|
Milling Vise with thumb screw, 2.125” opening x 2” wide |
| 1230* |
50.00 set
|
Milling Cutter Set, Includes five cutters, sizes 1/16, 3/32,1/8,
5/32 and 3/16 |
| 1230A* |
11.50 Ea. |
1/16 diameter Milling Cutter, 2 flute double end 3/16 shank,
mount directly in
3/16 collet |
| 1230B |
11.50 Ea. |
3/32 diameter Mifling Cutter, 2 flute double end 3/18 shank,
mount directly in
3/16 collet |
1230C * |
11.50 Ea.
|
1/8 diameter Milling Cutter, 2 flute double mid 3/16 shank,
mount directly in 3/16 count
|
1230D *
|
11.50 Ea.
|
5/32 diameter Milling Cutter, 2 flute doub~o end 3/16 shank
mount directly in 3/16 coliet |
1230E *
|
11.50 Ea.
|
3/16 diameter Milling Cutter, 2 flute double end 3/16 shank
mount iftrectty hi
3/16 collet |
1250 *
|
24.50 set
|
Riser Block Kit, for headstock and tool post, proyides 6.00
swing (riser for
tailstock not Included) |
| 1251 |
19.75 Ea. |
Tailstock Riser only |
1300 |
8.25 Ea. |
Booklet - “How To Run A Lathe” The Care and
Operation of A Screw Cutting Lathe, 123 pages |
| 1305 NEW |
22.95 Ea. |
Book- "The Taig Lathe” by Tony Jeffree, 180 pages |
| 1310 * |
7.50 Ea. |
Wrench for Spindle, 1” wide |
